Gunsmithing
Firearm Repair
- General Firearm Repair, Hourly: $95.00 (minimum of 1.5-2 hours for most repairs)
- Test Firing, Per Round: based off cost of ammo used
Firearm Cleaning
- General Firearm Cleaning, Hourly: $95.00
- Basic Field Cleaning on Simple Pistols (Glock M&P etc): $50.00
- Basic Field Cleaning on More Complex/Antique Pistols (Sigs, H&K, etc.): $95.00
- Detail Cleaning on Simple Pistols: $100.00
- Detail Cleaning/Inspection on Complex Firearms: $200.00
- Detail Cleaning/Inspection on Modern Bolt Actions: $150.00
- Detail Cleaning/Safety Inspection on Antique or Military Firearms: $250.00
- Detail Cleaning on Waterfowl Shotguns: $95.00-$150.00
Miscellaneous Gunsmithing
- General Gunsmithing, Hourly: $95.00
- Diagnostic Fee: $95.00 (covers a firearm inspection to build a quote and determine project feasibility)
- Basic Safety Inspection: A quick inspection to establish if the firearm is or could be safe to shoot
- Remove Stuck Empty or Cartridge: $50.00 (could move into hourly rate if difficult)
- Assemble Firearm from Parts: $150.00 (cost may be less but assume this much)
- NFA Engraving, Stripped Receiver: $75.00
- NFA Engraving, Assembled Receiver: $100.00
- Warranty Return to Manufacturer or Shipping to Other Vendor: $50.00 (+ actual shipping costs)
- Chamber Cast to Identify Unknown Chamber: $200.00
- Check Headspace, most firearms: $50.00
- Shipping: General shipping charges, varies
- Special Order Fee: $25.00 (sourcing unusual parts for customer, plus cost of parts)
AR-15 / AR-10 Work
- Assemble Lower From Parts (labor only, customer provides all parts): $75.00
- Assemble Upper from Parts (labor only, customer provides all parts): $85.00
- Assemble Complete Rifle from Parts (labor only, customer provides all parts): $150.00
- Install Single Part on AR (standard minimum charge): $50.00
- Install AR Trigger Kit (labor only, customer provides all parts): $75.00
- Install Muzzle Device, Crush Washer (labor only, customer provides crush washer, customer choice on Loctite/Rockset/nothing): $25.00
- Install Timed Muzzle Device, Shims (labor only, customer provides shims, customer choice on Loctite/Rockset/nothing): $30.00
- Pin and Weld Muzzle Device (customer provides all parts other than pin): $100.00
- NFA Engraving, Stripped Receiver (customer must include copy of submitted forms): $75.00
- NFA Engraving, Assembled Receiver (customer must include copy of submitted forms): $100.00
AK Work
- Install AK Trigger (customer provides all parts): $75.00
- Assemble AK from Parts, Rivet Work (stripped receiver): $350.00-$450
- Install AK Furniture, Each Piece (potential discount for set, assumes fitting will be needed): $50.00
- Basic Saiga Conversion, Labor Only: $150.00
- Thread AK Muzzle, Imperial Threads: $350.00
- Thread AK Muzzle, Metric Threads: $425.00
- Miscellaneous AK Work, Hourly: $100.00
- Refinish Ak- Parkerizing, Bluing, Cerakote, Etc: Price On Request
Muzzle Threading
- 1/2"-28tpi Muzzle Threads: $125.00
- 9/16"-24tpi Muzzle Threads: $125.00
- 5/8"-24tpi Muzzle Threads: $125.00
Muzzle Threading Modifiers
- Barrel Under 22": $65.00
- Cut Barrel and Crown Before Threading: $50.00
- Remount/Boresight Optic After Lathe Work: $30.00
Long Gun Chambering/Gunsmithing Barrel Chambering
- Standard Rifle Chambering, New Blank (Rem 700, Savage, Rem 700 clones, etc.): $500.00
- Installing Short Chambered Barrel (Hourly, may be less, but should expect up to this much): $350.00
- Controlled Feed or Other More Complex Barrel Install, New Blank: $550.00
- Controlled Feed or Other More Complex Barrel Install, Short Chambered Barrel: $450.00
Remington 700 Specific Work
- Install Rivet Type Extractor, Includes Parts: $150.00
- Install M-16 Style Extractor: $200.00
- Thread Bolt Handle for Extended Bolt Knob (will cold blue bolt handle, including Badger Bolt knob): $150.00
- Install New Trigger (minor fitting included, function and safety check when done): $50.00
General Stock Work
- General Inletting and Stock Fitting, Hourly: $95.00
- Install True Drop-In Rifle Stock (e.g., Magpul Hunter on Rem 700, no fitting required): $75.00
- Install Standard Rifle Stock, Some Fitting Expected (Boyds, SKS rifles, etc. May be less): $200.00
- Provide and Fit Oversize Action Screws, Rem 700 Pattern Only: $50.00
Recoil Pad Work
- Install Grind-to-Fit Recoil Pad (labor only, does not include pad): $95.00
Sling Stud / Other Hardware Install
- Drill for and Install Sling Studs, Each (includes studs): Pricing varies
Stock Bedding
- Bed Recoil Lug Area Only (no bedding pillars provided, stock refinish not required): $200.00
- Full Action Bedding (from recoil lug to rear tang, does not include bedding pillars, requires stock refinishing [not included]): $400.00
Refinish / Repair Work
- Standard Satin Finish Stock Refinish (dependent on preexisting damage/dents): $350.00
- High Gloss: $600.00
- Repair Cracked Wooden Stock, Hourly (Rifle will probably need to be checked in and inspected prior to any quote being given)
- Re-cut Factory Checkering, Grip Panels: $250.00
- Re-cut Factory Checkering, Forend Panels: $375.00
Drill and Tap / Other Machine Work
- Drill and Tap, Per Hole: $40.00
- Drill and Tap, Four Holes: $120.00
- Tear Down / Assembly Charge for Drill and Tap (assessed if extra work required for prep): $50.00
- Install New Shotgun Bead if Hole is Already There (labor only, does not include new bead): $50.00
Handgun Sight Work
- Install Glock Sight Set (usually while you wait): $35.00
- Standard Pistol Sight Set Install (most dovetail mounted pistols, unless listed specifically elsewhere): $75.00
- 1911 and XD Sight Set Installs: $125.00
- Machine Basic Dovetail (does not include any refinishing): $150.00
- Machine for Novak Style Rear Only (does not include any refinishing): $200.00
- Cut and Fill New Colored Front Sight Insert: $125.00
- Fill/Replace Damaged or Missing Colored Front Sight Insert: $75.00
- Install Pinned in Front Sight (does not include new pin, new sight should include pin): $75.00